Top sellers

Showing 1 - 17 of 17 items
  • $3.99

    2x 1mm thick silicon target steel for the OpenGrab EPM V3

    $3.99
  • Deprecated, replaced with V3R5C The EPM688-V2.5 is an Electro Permanent Magnet, combining the advantages of electro and permanent magnets. With virtually no power during steady state operation (<1mW) and 800mA for 1.2s during a switch cycle.  Holding force and consistency have been greatly improved (5kg under adverse conditions) and is more resistant...

  • $159.99

    The OpenGrab EPM v3 is an electropermanent magnet, combining the advantages of electro and permanent magnets. The device creates a very strong magnetic contact with a ferrous target. It supports UAVCAN, RC PWM and push button operation. OpenGrab EPM v3 has been developed by NicaDrone in cooperation with Zubax Robotics.

    $159.99
  • Deprecated, replaced with V3R5C The OpenGrab EPM v3 is an electropermanent magnet, combining the advantages of electro and permanent magnets. The device creates a very strong magnetic contact with a ferrous target. It supports UAVCAN, RC PWM and push button operation. OpenGrab EPM v3 has been developed by NicaDrone in cooperation with Zubax Robotics.

  • Deprecated, replaced with V3R5C This only exist for reference The EPM688-V2.0 is an Electro Permanent Magnet, combining the advantages of electro and permanent magnets. Ideal for cargo clamping on UAVs like quadrocopters. With virtually no power during steady state operation (<1mW) and 600mA for 0.3s during a switch cycle. 

  •   < Obsolete- replaced with EPM 688-V2.0 > The EPM688-5 is an Electro Permanent Magnet, combining the advantages of electro and permanent magnets. This Device comes with integrated electronics that can be operated with 3.3 and 5V TTL signals and uses 5V Vcc. It can hold up to 8kg. 

  • $143.89

    <Out of Stock> Everything you need to use Zubax GNSS with 3D Robotics Pixhawk v1, plus USB-UART adapter cable. The cable can be used to configure Zubax GNSS.

    $143.89
  • $4.99

    2 x 1 mm Silicon Target Steel  4 x M3x0.5x14 mm Standoff Brass Female -> Female 4 x M3x0.5 mm Stainless Steel Nylon Insert Lock Nut Metric 4 x M3x0.5x5 mm Stainless Metric Socket Head Screw  4 x M3x0.5x25 mm Stainless Metric Socket Head Screw 

    $4.99
  • $73.99

    Zubax DroneCode Probe is a generic JTAG / SWD + UART console adapter compatible with most ARM Cortex based designs and in particular with hardware maintained by the DroneCode project. The design is based on Black Magic Probe and is distributed under open source licenses. Learn more about its features and capabilities on the documentation page (link below).

    $73.99
  • $3.99

    1x CAN bus termination plug - UAVCAN Micro plug with a 120 Ω resistor between the pins CAN H and CAN L. 1x 20 cm cable with a standard UAVCAN Micro plug (CLIK-Mate, 4 circuits, 1.25 mm) on one end and a JST DF13 4-circuit plug (3D Robotics Pixhawk v1 compatible) on the other end.

    $3.99
  • $13.99

    10x 1mm thick silicon target steel for the OpenGrab EPM V3

    $13.99
  • $3.99

    1x CAN bus termination plug - JST-GH plug with a 120 Ω resistor between the pins CAN H and CAN L. 1x 20 cm cable with a standard JST-GH plug on end and a DF13 plug on the other. 3D Robotics Pixhawk compatible

    $3.99
  • Discontinued OGCAN is an open hardware CAN bus interface that allows you to control the EPM and to monitor its state via standard CAN bus or via serial CLI. Supported CAN protocols: CANaerospace, UAVCAN.

  • $3.99

    1x CAN bus termination plug - JST-GH plug with a 120 Ω resistor between the pins CAN H and CAN L. 1x 20 cm cable with a standard JST-GH plug / housing  on both ends. Standard UAVCAN cable, also compatible with Pixracer 

    $3.99
  • $6.99

    1x Standard UAVCAN cable, also compatible with Pixracer  1x UAVCAN cable 3D Robotics Pixhawk compatible 1x External Button  1x Programming JST-GH plug pigtail for firmware flashing and UART access 

    $6.99
  • $109.00

    <Out of Stock> High-performance open-source positioning module for outdoor environments, interfaced via doubly redundant UAVCAN bus. It includes a state-of-the-art GPS/GLONASS receiver, a high precision barometer and a 3-axis compass.

    $109.00
  • $114.89

    <Out of stock> Everything you need to use Zubax GNSS with 3D Robotics Pixhawk v1. Note that this kit does not include a USB-UART adapter cable, but this other kit does. The adapter cable provides a more convenient way to configure Zubax GNSS than UAVCAN.

    $114.89
Showing 1 - 17 of 17 items